Represents a Die Throat Child sub feature. More...

Inheritance diagram for NXOpen::Die::ThroatChildBuilder:

Public Types
enum	TypeOption { TypeOptionWipe, TypeOptionRestrike }
	Settings for the type of the throat section. More...

Public Member Functions
NXOpen::Die::DieBuildStatusOption	BuildStatus ()
	Returns the build status of the throat section.

NXOpen::Expression *	CavityDepth ()
	Returns the distance measured from the bend profile of the flange to the base of the throat.

NXOpen::Expression *	CavityOffset ()
	Returns the offset distance measured from the Throat CSYS to the back cavity area of the throat.

bool	DesignStatus ()
	Returns the design status of the throat section, if true the throat section will be built into the model, if false it will not.

bool	DisplayStatus ()
	Returns the display status of the throat section, if true input data to the throat section will be displayed, if false the input data will not be displayed.

NXOpen::Expression *	ExtensionLength ()
	Returns the tangent distance to add to the end of the flange.

void	GetCavityAttributes (NXString title, NXString value, int *color)
	Gets the cavity attributes, note existance of attributes depends on usage in main feature.

void	GetExtensionAttributes (NXString title, NXString value, int *color)
	Gets the extension attributes, note existance of attributes depends on usage in main feature.

NXOpen::Expression *	LowerRadius ()
	Returns the radius to apply to the lower corner of the throat cavity.

double	Radius ()
	Returns the radius to be applied at the back of the throat, top and bottom Created in NX4.0.0.

NXOpen::Expression *	SectionPlacement ()
	Returns the throat section placement along the center line, an expression containg the length along the centerline for placement Created in NX4.0.0.

void	SetCavityAttributes (const NXString &title, const NXString &value, int color)
	Sets the cavity attributes, note existance of attributes depends on usage in main feature.

void	SetCavityAttributes (const char title, const char value, int color)
	Sets the cavity attributes, note existance of attributes depends on usage in main feature.

void	SetCavityDepth (const NXString &cavityDepth)
	Created in NX4.0.0.

void	SetCavityDepth (const char *cavityDepth)
	Created in NX4.0.0.

void	SetCavityOffset (const NXString &cavityOffset)
	Created in NX4.0.0.

void	SetCavityOffset (const char *cavityOffset)
	Created in NX4.0.0.

void	SetDesignStatus (bool designStatus)
	Sets the design status of the throat section, if true the throat section will be built into the model, if false it will not.

void	SetDisplayStatus (bool displayStatus)
	Sets the display status of the throat section, if true input data to the throat section will be displayed, if false the input data will not be displayed.

void	SetExtensionAttributes (const NXString &title, const NXString &value, int color)
	Sets the extension attributes, note existance of attributes depends on usage in main feature.

void	SetExtensionAttributes (const char title, const char value, int color)
	Sets the extension attributes, note existance of attributes depends on usage in main feature.

void	SetExtensionLength (const NXString &extensionLength)
	Created in NX4.0.0.

void	SetExtensionLength (const char *extensionLength)
	Created in NX4.0.0.

void	SetLowerRadius (const NXString &lowerRadius)
	Created in NX4.0.0.

void	SetLowerRadius (const char *lowerRadius)
	Created in NX4.0.0.

void	SetRadius (double radius)
	Sets the radius to be applied at the back of the throat, top and bottom Created in NX4.0.0.

void	SetSectionPlacement (const NXString &sectionPlacement)
	Created in NX4.0.0.

void	SetSectionPlacement (const char *sectionPlacement)
	Created in NX4.0.0.

void	SetStep (double step)
	Sets the step to be applied at the end of the tangent extension of the flange Created in NX4.0.0.

void	SetStepDistance (const NXString &stepDistance)
	Created in NX4.0.0.

void	SetStepDistance (const char *stepDistance)
	Created in NX4.0.0.

void	SetUpperRadius (const NXString &upperRadius)
	Created in NX4.0.0.

void	SetUpperRadius (const char *upperRadius)
	Created in NX4.0.0.

double	Step ()
	Returns the step to be applied at the end of the tangent extension of the flange Created in NX4.0.0.

NXOpen::Expression *	StepDistance ()
	Returns the step distance to add at the end of the tangent extension.

NXOpen::Expression *	UpperRadius ()
	Returns the radius to apply to the upper corner of the throat cavity.

Public Member Functions inherited from NXOpen::Features::FeatureBuilder
NXOpen::Features::Feature *	CommitFeature ()
	Commits the feature parameters and creates the feature.

NXOpen::Features::Feature *	GetFeature ()
	Returns the feature currently being edited by this builder.

void	HideInternalParentFeatureAfterEdit (NXOpen::Features::Feature *parentFeature)
	Re-suppress an internal parent feature (a slave feature) after it has been edited.

bool	ParentFeatureInternal ()
	Returns whether or not the latest timestamped parent feature of this feature should be made internal Created in NX5.0.0.

bool	PatchSolutionFlag ()
	Returns the patch solution flag Created in NX8.0.1.

NXString	PatchSurfaceFilename ()
	Returns the patch surface filename Created in NX8.0.1.

void	SetParentFeatureInternal (NXOpen::Features::Feature *parentFeature)
	Set the parent features which would be internal or slaves to the feature being created or commited Created in NX6.0.0.

void	SetParentFeatureInternal (bool isInternal)
	Sets whether or not the latest timestamped parent feature of this feature should be made internal Created in NX5.0.0.

void	SetPatchSolutionFlag (bool optionValue)
	Sets the patch solution flag Created in NX8.0.1.

void	SetPatchSurfaceFilename (const NXString &surfaceFilename)
	Sets the patch surface filename Created in NX8.0.1.

void	SetPatchSurfaceFilename (const char *surfaceFilename)
	Sets the patch surface filename Created in NX8.0.1.

void	SetSurroundingPatchSurfaceFilename (const NXString &surroundingSurfaceFilename)
	Sets the surrounding patch surface filename Created in NX8.0.1.

void	SetSurroundingPatchSurfaceFilename (const char *surroundingSurfaceFilename)
	Sets the surrounding patch surface filename Created in NX8.0.1.

void	ShowInternalParentFeatureForEdit (NXOpen::Features::Feature *parentFeature)
	Unsuppress an internal parent feature (a slave feature) so it can be edited.

NXString	SurroundingPatchSurfaceFilename ()
	Returns the surrounding patch surface filename Created in NX8.0.1.

void	UnsetParentFeatureInternal (NXOpen::Features::Feature *parentFeature)
	Set the internal parent feature of the feature being edited to external Created in NX6.0.0.

Public Member Functions inherited from NXOpen::Builder
NXOpen::NXObject *	Commit ()
	Commits any edits that have been applied to the builder.

void	Destroy ()
	Deletes the builder, and cleans up any objects created by the builder.

std::vector< NXOpen::NXObject * >	GetCommittedObjects ()
	For builders that create more than one object, this method returns the objects that are created by commit.

NXOpen::NXObject *	GetObject ()
	Returns the object currently being edited by this builder.

void	ShowResults ()
	Updates the model to reflect the result of an edit to the model for all builders that support showing results.

virtual bool	Validate ()
	Validate whether the inputs to the component are sufficient for commit to be called.

Public Member Functions inherited from NXOpen::TaggedObject
tag_t	GetTag () const
	<b>Deprecated</b>:<br> Use Tag instead.

tag_t	Tag () const
	Returns the tag of this object.

Detailed Description

Represents a Die Throat Child sub feature.

This sub feature is created via the main feature builder.

Created in NX4.0.0.

Member Enumeration Documentation

enum NXOpen::Die::ThroatChildBuilder::TypeOption

Settings for the type of the throat section.

Enumerator:

TypeOptionWipe	Throat section is built for a wipe operation.
TypeOptionRestrike	Throat section is built for a restrike operation.

Member Function Documentation

NXOpen::Die::DieBuildStatusOption NXOpen::Die::ThroatChildBuilder::BuildStatus ( )

Returns the build status of the throat section.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::CavityDepth ( )

Returns the distance measured from the bend profile of the flange to the base of the throat.

The base of the throat is considered to be the surface the wear plates are mounted on for guiding and aliging the flange steels. The value given must be larger than the minimum cavity depth. An expression containg the value. Value is used in both the Wipe and Restrike Flange.
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::CavityOffset ( )

Returns the offset distance measured from the Throat CSYS to the back cavity area of the throat.

Both positive and negative values may given to adjust the cavity to the proper location. An expression containg the value. Value is used in both the Wipe and Restrike Flange.
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

bool NXOpen::Die::ThroatChildBuilder::DesignStatus ( )

Returns the design status of the throat section, if true the throat section will be built into the model, if false it will not.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

bool NXOpen::Die::ThroatChildBuilder::DisplayStatus ( )

Returns the display status of the throat section, if true input data to the throat section will be displayed, if false the input data will not be displayed.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::ExtensionLength ( )

Returns the tangent distance to add to the end of the flange.

   An expression containg the length along the tangent.
   Value is used in both the Wipe and Restrike Flange.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

void NXOpen::Die::ThroatChildBuilder::GetCavityAttributes	(	NXString *	title,
		NXString *	value,
		int *	color
	)

Gets the cavity attributes, note existance of attributes depends on usage in main feature.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

title	Title for attribute.
value	Value of attribute.
color	Color of cavity faces.

void NXOpen::Die::ThroatChildBuilder::GetExtensionAttributes	(	NXString *	title,
		NXString *	value,
		int *	color
	)

Gets the extension attributes, note existance of attributes depends on usage in main feature.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

title	Title for attribute.
value	Value of attribute.
color	Color of extension faces.

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::LowerRadius ( )

Returns the radius to apply to the lower corner of the throat cavity.

   Typically, both the lower and the upper radius will be the
   same. An expression containg the value.
   Value is used in both the Wipe and Restrike Flange.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

double NXOpen::Die::ThroatChildBuilder::Radius ( )

Returns the radius to be applied at the back of the throat, top and bottom
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::SectionPlacement ( )

Returns the throat section placement along the center line, an expression containg the length along the centerline for placement
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

void NXOpen::Die::ThroatChildBuilder::SetCavityAttributes	(	const NXString &	title,
		const NXString &	value,
		int	color
	)

Sets the cavity attributes, note existance of attributes depends on usage in main feature.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

title	Title for attribute. NOTE: The full Unicode character set is not supported for this parameter.
value	Value of attribute. NOTE: The full Unicode character set is not supported for this parameter.
color	Color of cavity faces.

void NXOpen::Die::ThroatChildBuilder::SetCavityAttributes	(	const char *	title,
		const char *	value,
		int	color
	)

Sets the cavity attributes, note existance of attributes depends on usage in main feature.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

title	Title for attribute. NOTE: The full Unicode character set is not supported for this parameter.
value	Value of attribute. NOTE: The full Unicode character set is not supported for this parameter.
color	Color of cavity faces.

void NXOpen::Die::ThroatChildBuilder::SetCavityDepth ( const NXString & cavityDepth )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

cavityDepth NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetCavityDepth ( const char * cavityDepth )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

cavityDepth NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetCavityOffset ( const NXString & cavityOffset )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

cavityOffset NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetCavityOffset ( const char * cavityOffset )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

cavityOffset NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetDesignStatus ( bool designStatus )

Sets the design status of the throat section, if true the throat section will be built into the model, if false it will not.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

designStatus design status

void NXOpen::Die::ThroatChildBuilder::SetDisplayStatus ( bool displayStatus )

Sets the display status of the throat section, if true input data to the throat section will be displayed, if false the input data will not be displayed.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

displayStatus display status

void NXOpen::Die::ThroatChildBuilder::SetExtensionAttributes	(	const NXString &	title,
		const NXString &	value,
		int	color
	)

Sets the extension attributes, note existance of attributes depends on usage in main feature.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

title	Title for attribute. NOTE: The full Unicode character set is not supported for this parameter.
value	Value of attribute. NOTE: The full Unicode character set is not supported for this parameter.
color	Color of extension faces.

void NXOpen::Die::ThroatChildBuilder::SetExtensionAttributes	(	const char *	title,
		const char *	value,
		int	color
	)

Sets the extension attributes, note existance of attributes depends on usage in main feature.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

title	Title for attribute. NOTE: The full Unicode character set is not supported for this parameter.
value	Value of attribute. NOTE: The full Unicode character set is not supported for this parameter.
color	Color of extension faces.

void NXOpen::Die::ThroatChildBuilder::SetExtensionLength ( const NXString & extensionLength )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

extensionLength NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetExtensionLength ( const char * extensionLength )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

extensionLength NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetLowerRadius ( const NXString & lowerRadius )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

lowerRadius NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetLowerRadius ( const char * lowerRadius )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

lowerRadius NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetRadius ( double radius )

Sets the radius to be applied at the back of the throat, top and bottom
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

radius radius

void NXOpen::Die::ThroatChildBuilder::SetSectionPlacement ( const NXString & sectionPlacement )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

sectionPlacement NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetSectionPlacement ( const char * sectionPlacement )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

sectionPlacement NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetStep ( double step )

Sets the step to be applied at the end of the tangent extension of the flange
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

step step

void NXOpen::Die::ThroatChildBuilder::SetStepDistance ( const NXString & stepDistance )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

stepDistance NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetStepDistance ( const char * stepDistance )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

stepDistance NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetUpperRadius ( const NXString & upperRadius )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

upperRadius NOTE: The full Unicode character set is not supported for this parameter.

void NXOpen::Die::ThroatChildBuilder::SetUpperRadius ( const char * upperRadius )

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

Parameters

upperRadius NOTE: The full Unicode character set is not supported for this parameter.

double NXOpen::Die::ThroatChildBuilder::Step ( )

Returns the step to be applied at the end of the tangent extension of the flange
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::StepDistance ( )

Returns the step distance to add at the end of the tangent extension.

The step is at a right angle and only applies to the Wipe Flange. An expression containg the step distance.
Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

NXOpen::Expression* NXOpen::Die::ThroatChildBuilder::UpperRadius ( )

Returns the radius to apply to the upper corner of the throat cavity.

   An expression containg the value.
   Value is used in both the Wipe and Restrike Flange.

Created in NX4.0.0.

License requirements : ug_die_design ("Die Design")

The documentation for this class was generated from the following file:

Die_ThroatChildBuilder.hxx

Public Types

Public Member Functions

Detailed Description

Member Enumeration Documentation

Member Function Documentation