Represents a CAM::MillCutParameters. More...

Inheritance diagram for NXOpen::CAM::MillCutParameters:

Public Member Functions
NXOpen::CAM::AcrossVoids *	AcrossVoids ()
	Returns the across voids Created in NX6.0.0.

NXOpen::CAM::CutParametersActionWhenGougingTypes	ActionWhenGouging ()
	Returns the action when gouging Created in NX6.0.0.

NXOpen::CAM::CutParametersAdjacentBladesTypes	AdjacentBlades ()
	Returns the Adjacent Blades Stock Option Type Created in NX8.5.0.

bool	AllowUndercutting ()
	Returns the allow undercutting toggle Created in NX8.0.0.

bool	ApplyToLastPass ()
	Returns the status for doing Blank Sensitive finish on the last cut level Created in NX7.5.1.

NXOpen::CAM::InheritableDoubleBuilder *	BladeStock ()
	Returns the blade stock Created in NX7.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	BlankDistance ()
	Returns the blank distance Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	BlankOverhang ()
	Returns the blank overhang (inheritable tool dependent).

NXOpen::CAM::InheritableDoubleBuilder *	BlankStock ()
	Returns the blank stock Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	BlendStock ()
	Returns the blend stock Created in NX7.0.0.

bool	BoundaryApproximation ()
	Returns the boundary approximation toggle Created in NX6.0.0.

double	BoundaryInTol ()
	Returns the boundary intol Created in NX6.0.0.

double	BoundaryOutTol ()
	Returns the boundary out tol Created in NX6.0.0.

double	BoundaryStock ()
	Returns the boundary stock Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	CheckStock ()
	Returns the check stock Created in NX6.0.0.

NXOpen::CAM::CleanupOutput *	CleanupOutput ()
	Returns the Cleanup Output Created in NX6.0.0.

NXOpen::CAM::CleanupSettings *	CleanupSettings ()
	Returns the Cleanup Settings Created in NX6.0.0.

NXOpen::CAM::CornerControlBuilder *	CornerControl ()
	Returns the corner control Created in NX6.0.0.

NXOpen::CAM::CutParametersCornerFindingTypes	CornerFindingOptions ()
	Returns the Corner Finding Options Created in NX7.5.0.

NXOpen::CAM::CutAngle *	CutAngle ()
	Returns the cut angle Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	CutAreaExtensionDistance ()
	Returns the cut area extension distance builder Created in NX6.0.0.

bool	CutBelowOverhangingBlank ()
	Returns the Cut Below Overhanging Blank Method Created in NX9.0.0.

bool	CutBelowToolContact ()
	Returns the cut below tool contact setting Created in NX6.0.0.

bool	CutBetweenLevels ()
	Returns the cut between levels Created in NX6.0.0.

NXOpen::CAM::CutDirection *	CutDirection ()
	Returns the cut direction Created in NX6.0.0.

NXOpen::CAM::CutParametersCutOrderTypes	CutOrder ()
	Returns the cut order Created in NX6.0.0.

bool	CutWallsOnly ()
	Returns the Cut Walls Only toggle Created in NX6.0.0.

NXOpen::CAM::ExtendAtEdges *	ExtendAtEdges ()
	Returns the Extend At Edges Created in NX6.0.0.

NXOpen::CAM::CutParametersExtendFloorTypes	ExtendFloorTo ()
	Returns the extend floor to Created in NX8.0.0.

bool	ExtendToPart ()
	Returns the extend to part flag Created in NX6.0.0.

NXOpen::CAM::FinishPassesBuilder *	FinishPasses ()
	Returns the finish passes Created in NX6.0.0.

bool	FloorSameAsPartStock ()
	Returns the floor same as part stock Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	FloorStock ()
	Returns the floor stock Created in NX6.0.0.

bool	FollowCheck ()
	Returns the follow check geometry status Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	FromLeadingEdge ()
	Returns the from leading edge Created in NX7.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	FromTrailingEdge ()
	Returns the from trailing edge Created in NX7.0.0.

bool	GlobalOptimization ()
	Returns the global optimzation status Created in NX7.5.0.

NXOpen::CAM::InheritableDoubleBuilder *	HubStock ()
	Returns the hub stock Created in NX7.0.0.

bool	IncludeBodiesOfSurfaceRegion ()
	Returns the flag to check bodies of surface region Created in NX8.0.0.

NXOpen::CAM::LevelToLevel *	LevelToLevel ()
	Returns the Level to Level Created in NX6.0.0.

NXOpen::CAM::LowerLimit *	LowerLimit ()
	Returns the lower limit Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	MaxCutStep ()
	Returns the maximum cut step Created in NX6.0.0.

NXOpen::CAM::MaxCutTraverse *	MaxCutTraverse ()
	Returns the max cut traverse Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	MergeDistance ()
	Returns the merge distance builder (tool dependent double) Created in NX6.0.0.

NXOpen::CAM::MinCutVolume *	MinCutVolume ()
	Returns the minimum cut volume Created in NX6.0.0.

bool	MinimizeNumberOfEngages ()
	Returns the minimize number of engages toggle Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	MinMaterialThickness ()
	Returns the minimum material thickness Created in NX6.0.0.

NXOpen::CAM::MultiDepthCut *	MultiDepthCut ()
	Returns the Multi Depth Cut Created in NX6.0.0.

NXOpen::CAM::OutputUncutRegions *	OutputUncutRegions ()
	Returns the output uncut regions Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	PartStockOffset ()
	Returns the part stock offset Created in NX6.0.0.

NXOpen::CAM::CutParametersPatternDirectionTypes	PatternDirection ()
	Returns the pattern direction Created in NX6.0.0.

NXOpen::CAM::CutParametersPlungeDirectionTypes	PlungeDirection ()
	Returns the plunge direction Created in NX6.0.0.

bool	PreventUndercutting ()
	Returns the prevent undercutting toggle This property is deprecated.

bool	RegionConnection ()
	Returns the region connection Created in NX6.0.0.

NXOpen::CAM::CutParametersRegionSequencingTypes	RegionSequencing ()
	Returns the region resequencing Created in NX6.0.0.

bool	RollToolOverEdges ()
	Returns the roll tool over edges toggle Created in NX6.0.0.

double	RotaryMaxAngleLimit ()
	Returns the rotary max angle limit Created in NX8.0.0.

double	RotaryMinAngleLimit ()
	Returns the min angle from part axis Created in NX8.0.0.

bool	SelfIntersection ()
	Returns the Standard Drive Self-Intersect Status Created in NX6.0.0.

void	SetActionWhenGouging (NXOpen::CAM::CutParametersActionWhenGougingTypes propValue)
	Sets the action when gouging Created in NX6.0.0.

void	SetAdjacentBlades (NXOpen::CAM::CutParametersAdjacentBladesTypes adjacentBlades)
	Sets the Adjacent Blades Stock Option Type Created in NX8.5.0.

void	SetAllowUndercutting (bool propValue)
	Sets the allow undercutting toggle Created in NX8.0.0.

void	SetApplyToLastPass (bool applyLastPassStatus)
	Sets the status for doing Blank Sensitive finish on the last cut level Created in NX7.5.1.

void	SetBoundaryApproximation (bool propValue)
	Sets the boundary approximation toggle Created in NX6.0.0.

void	SetBoundaryInTol (double propValue)
	Sets the boundary intol Created in NX6.0.0.

void	SetBoundaryOutTol (double propValue)
	Sets the boundary out tol Created in NX6.0.0.

void	SetBoundaryStock (double propValue)
	Sets the boundary stock Created in NX6.0.0.

void	SetCornerFindingOptions (NXOpen::CAM::CutParametersCornerFindingTypes cornerFinding)
	Sets the Corner Finding Options Created in NX7.5.0.

void	SetCutBelowOverhangingBlank (bool propValue)
	Sets the Cut Below Overhanging Blank Method Created in NX9.0.0.

void	SetCutBelowToolContact (bool cutBelowToolContact)
	Sets the cut below tool contact setting Created in NX6.0.0.

void	SetCutBetweenLevels (bool cutBetween)
	Sets the cut between levels Created in NX6.0.0.

void	SetCutOrder (NXOpen::CAM::CutParametersCutOrderTypes propValue)
	Sets the cut order Created in NX6.0.0.

void	SetCutWallsOnly (bool propValue)
	Sets the Cut Walls Only toggle Created in NX6.0.0.

void	SetExtendFloorTo (NXOpen::CAM::CutParametersExtendFloorTypes option)
	Sets the extend floor to Created in NX8.0.0.

void	SetExtendToPart (bool flag)
	Sets the extend to part flag Created in NX6.0.0.

void	SetFloorSameAsPartStock (bool stockPartStatus)
	Sets the floor same as part stock Created in NX6.0.0.

void	SetFollowCheck (bool propValue)
	Sets the follow check geometry status Created in NX6.0.0.

void	SetGlobalOptimization (bool globalOptStatus)
	Sets the global optimzation status Created in NX7.5.0.

void	SetIncludeBodiesOfSurfaceRegion (bool includeBodies)
	Sets the flag to check bodies of surface region Created in NX8.0.0.

void	SetMinimizeNumberOfEngages (bool propValue)
	Sets the minimize number of engages toggle Created in NX6.0.0.

void	SetPatternDirection (NXOpen::CAM::CutParametersPatternDirectionTypes propValue)
	Sets the pattern direction Created in NX6.0.0.

void	SetPlungeDirection (NXOpen::CAM::CutParametersPlungeDirectionTypes propValue)
	Sets the plunge direction Created in NX6.0.0.

void	SetPreventUndercutting (bool propValue)
	Sets the prevent undercutting toggle This property is deprecated.

void	SetRegionConnection (bool propValue)
	Sets the region connection Created in NX6.0.0.

void	SetRegionSequencing (NXOpen::CAM::CutParametersRegionSequencingTypes propValue)
	Sets the region resequencing Created in NX6.0.0.

void	SetRollToolOverEdges (bool propValue)
	Sets the roll tool over edges toggle Created in NX6.0.0.

void	SetRotaryMaxAngleLimit (double angle)
	Sets the rotary max angle limit Created in NX8.0.0.

void	SetRotaryMinAngleLimit (double angle)
	Sets the min angle from part axis Created in NX8.0.0.

void	SetSelfIntersection (bool selfIntersect)
	Sets the Standard Drive Self-Intersect Status Created in NX6.0.0.

void	SetSimplifyShapes (NXOpen::CAM::CutParametersSimplifyShapesTypes propValue)
	Sets the Simplify Shapes Method Created in NX6.0.0.

void	SetTlaxisBladeRollAngle (double angle)
	Sets the max blade roll angle Created in NX7.0.0.

void	SetTolerantMachining (bool tolerantMachine)
	Sets the tolerant machining status Created in NX6.0.0.

void	SetToolAxisSmoothing (int smoothing)
	Sets the degree of tool axis smoothing Created in NX7.0.0.

void	SetToolpathSmoothing (int smoothing)
	Sets the degree of tool path smoothing Created in NX7.0.0.

void	SetToolRunOffType (NXOpen::CAM::CutParametersToolRunOffTypes toolRunOff)
	Sets the Tool Run Off Type Created in NX8.0.0.

void	SetTraverseOpenPasses (NXOpen::CAM::CutParametersTraverseOpenPassesTypes propValue)
	Sets the open passes Created in NX6.0.0.

void	SetTrimControl (NXOpen::CAM::CutParametersTrimControlTypes propValue)
	Sets the trim control method type Created in NX6.0.0.

void	SetUsePrevious2dIpw (bool propValue)
	Sets the use previous IPW toggle Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	ShroudStock ()
	Returns the shroud stock Created in NX7.0.0.

NXOpen::CAM::CutParametersSimplifyShapesTypes	SimplifyShapes ()
	Returns the Simplify Shapes Method Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	SinglePassOffset ()
	Returns the Single Pass Offset Created in NX8.0.0.

NXOpen::CAM::SmallAreaAvoidance *	SmallAreaAvoidance ()
	Returns the small area avoidance Created in NX6.0.0.

NXOpen::CAM::SteepContainment *	SteepContainment ()
	Returns the steep containment Created in NX6.0.0.

NXOpen::CAM::StepoverBuilder *	Stepover ()
	Returns the stepover Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	StepoverLimit ()
	Returns the Stepover Limit Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	TextDepth ()
	Returns the Text Depth Created in NX6.0.0.

double	TlaxisBladeRollAngle ()
	Returns the max blade roll angle Created in NX7.0.0.

bool	TolerantMachining ()
	Returns the tolerant machining status Created in NX6.0.0.

NXOpen::CAM::ToolAxisChange *	ToolAxisChange ()
	Returns the tool axis change Created in NX6.0.0.

int	ToolAxisSmoothing ()
	Returns the degree of tool axis smoothing Created in NX7.0.0.

NXOpen::CAM::ToolAxisTilt *	ToolAxisTilt ()
	Returns the tool axis tilt Created in NX6.0.0.

int	ToolpathSmoothing ()
	Returns the degree of tool path smoothing Created in NX7.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	ToolRunOff ()
	Returns the Tool Run Off Created in NX8.0.0.

NXOpen::CAM::CutParametersToolRunOffTypes	ToolRunOffType ()
	Returns the Tool Run Off Type Created in NX8.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	ToolRunOn ()
	Returns the Tool Run On Created in NX8.0.0.

NXOpen::CAM::CutParametersTraverseOpenPassesTypes	TraverseOpenPasses ()
	Returns the open passes Created in NX6.0.0.

NXOpen::CAM::CutParametersTrimControlTypes	TrimControl ()
	Returns the trim control method type Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	TrimStock ()
	Returns the trim stock Created in NX6.0.0.

NXOpen::CAM::TrochoidalSettings *	TrochoidalSettings ()
	Returns the Trochoidal Settings Created in NX6.0.0.

NXOpen::CAM::UpDownCutting *	UpDownCutting ()
	Returns the up down cutting Created in NX6.0.0.

bool	UsePrevious2dIpw ()
	Returns the use previous IPW toggle Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	ValleyOverlapDistance ()
	Returns the valley overlap distance Created in NX6.0.0.

NXOpen::CAM::InheritableDoubleBuilder *	WallStock ()
	Returns the wall stock Created in NX6.0.0.

NXOpen::CAM::ZAxisSmoothing *	ZAxisSmoothing ()
	Returns the Z Axis Smoothing.

Public Member Functions inherited from NXOpen::CAM::CutParameters
bool	CheckIpwCollisions ()
	Returns the value to Check for Ipw Collsions Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	CheckSafeClearance ()
	Returns the Check Safe Clearance Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	HolderClearance ()
	Returns the Holder Clearance Created in NX8.0.0.

NXOpen::CAM::CutParametersIpwTypes	IpwType ()
	Returns the IPW type Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	NeckClearance ()
	Returns the Neck Clearance Created in NX8.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	PartSafeClearance ()
	Returns the Part Safe Clearance

NXOpen::CAM::InheritableDoubleBuilder *	PartStock ()
	Returns the part stock Created in NX6.0.0.

void	SetCheckIpwCollisions (bool flag)
	Sets the value to Check for Ipw Collsions Created in NX6.0.0.

void	SetIpwType (NXOpen::CAM::CutParametersIpwTypes propValue)
	Sets the IPW type Created in NX6.0.0.

void	SetUseToolHolder (bool propValue)
	Sets the use tool holder Created in NX6.0.0.

NXOpen::CAM::InheritableToolDepBuilder *	ShankClearance ()
	Returns the Shank Clearance Created in NX8.0.0.

NXOpen::CAM::Inheritable2dLength *	Tolerances ()
	Returns the Tolerances builder Created in NX7.5.0.

bool	UseToolHolder ()
	Returns the use tool holder Created in NX6.0.0.

Public Member Functions inherited from NXOpen::TaggedObject
tag_t	GetTag () const
	<b>Deprecated</b>:<br> Use Tag instead.

tag_t	Tag () const
	Returns the tag of this object.

Detailed Description

Represents a CAM::MillCutParameters.

Created in NX6.0.0.

Member Function Documentation

NXOpen::CAM::AcrossVoids* NXOpen::CAM::MillCutParameters::AcrossVoids ( )

Returns the across voids
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersActionWhenGougingTypes NXOpen::CAM::MillCutParameters::ActionWhenGouging ( )

Returns the action when gouging
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersAdjacentBladesTypes NXOpen::CAM::MillCutParameters::AdjacentBlades ( )

Returns the Adjacent Blades Stock Option Type
Created in NX8.5.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::AllowUndercutting ( )

Returns the allow undercutting toggle
Created in NX8.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::ApplyToLastPass ( )

Returns the status for doing Blank Sensitive finish on the last cut level
Created in NX7.5.1.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::BladeStock ( )

Returns the blade stock
Created in NX7.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::BlankDistance ( )

Returns the blank distance
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::BlankOverhang ( )

Returns the blank overhang (inheritable tool dependent).

       Its relative UI name is changed to "Tool Overhang" from NX8.0. 
       But it is named to "First Pass Overhang" in floor milling and floor and wall milling

Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::BlankStock ( )

Returns the blank stock
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::BlendStock ( )

Returns the blend stock
Created in NX7.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::BoundaryApproximation ( )

Returns the boundary approximation toggle
Created in NX6.0.0.

License requirements : None

double NXOpen::CAM::MillCutParameters::BoundaryInTol ( )

Returns the boundary intol
Created in NX6.0.0.

License requirements : None

double NXOpen::CAM::MillCutParameters::BoundaryOutTol ( )

Returns the boundary out tol
Created in NX6.0.0.

License requirements : None

double NXOpen::CAM::MillCutParameters::BoundaryStock ( )

Returns the boundary stock
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::CheckStock ( )

Returns the check stock
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CleanupOutput* NXOpen::CAM::MillCutParameters::CleanupOutput ( )

Returns the Cleanup Output
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CleanupSettings* NXOpen::CAM::MillCutParameters::CleanupSettings ( )

Returns the Cleanup Settings
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CornerControlBuilder* NXOpen::CAM::MillCutParameters::CornerControl ( )

Returns the corner control
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersCornerFindingTypes NXOpen::CAM::MillCutParameters::CornerFindingOptions ( )

Returns the Corner Finding Options
Created in NX7.5.0.

License requirements : None

NXOpen::CAM::CutAngle* NXOpen::CAM::MillCutParameters::CutAngle ( )

Returns the cut angle
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::CutAreaExtensionDistance ( )

Returns the cut area extension distance builder
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::CutBelowOverhangingBlank ( )

Returns the Cut Below Overhanging Blank Method
Created in NX9.0.0.

License requirements : cam_base ("CAM BASE")

bool NXOpen::CAM::MillCutParameters::CutBelowToolContact ( )

Returns the cut below tool contact setting
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::CutBetweenLevels ( )

Returns the cut between levels
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutDirection* NXOpen::CAM::MillCutParameters::CutDirection ( )

Returns the cut direction
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersCutOrderTypes NXOpen::CAM::MillCutParameters::CutOrder ( )

Returns the cut order
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::CutWallsOnly ( )

Returns the Cut Walls Only toggle
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::ExtendAtEdges* NXOpen::CAM::MillCutParameters::ExtendAtEdges ( )

Returns the Extend At Edges
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersExtendFloorTypes NXOpen::CAM::MillCutParameters::ExtendFloorTo ( )

Returns the extend floor to
Created in NX8.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::ExtendToPart ( )

Returns the extend to part flag
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::FinishPassesBuilder* NXOpen::CAM::MillCutParameters::FinishPasses ( )

Returns the finish passes
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::FloorSameAsPartStock ( )

Returns the floor same as part stock
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::FloorStock ( )

Returns the floor stock
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::FollowCheck ( )

Returns the follow check geometry status
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::FromLeadingEdge ( )

Returns the from leading edge
Created in NX7.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::FromTrailingEdge ( )

Returns the from trailing edge
Created in NX7.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::GlobalOptimization ( )

Returns the global optimzation status
Created in NX7.5.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::HubStock ( )

Returns the hub stock
Created in NX7.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::IncludeBodiesOfSurfaceRegion ( )

Returns the flag to check bodies of surface region
Created in NX8.0.0.

License requirements : None

NXOpen::CAM::LevelToLevel* NXOpen::CAM::MillCutParameters::LevelToLevel ( )

Returns the Level to Level
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::LowerLimit* NXOpen::CAM::MillCutParameters::LowerLimit ( )

Returns the lower limit
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::MaxCutStep ( )

Returns the maximum cut step
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::MaxCutTraverse* NXOpen::CAM::MillCutParameters::MaxCutTraverse ( )

Returns the max cut traverse
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::MergeDistance ( )

Returns the merge distance builder (tool dependent double)
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::MinCutVolume* NXOpen::CAM::MillCutParameters::MinCutVolume ( )

Returns the minimum cut volume
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::MinimizeNumberOfEngages ( )

Returns the minimize number of engages toggle
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::MinMaterialThickness ( )

Returns the minimum material thickness
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::MultiDepthCut* NXOpen::CAM::MillCutParameters::MultiDepthCut ( )

Returns the Multi Depth Cut
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::OutputUncutRegions* NXOpen::CAM::MillCutParameters::OutputUncutRegions ( )

Returns the output uncut regions
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::PartStockOffset ( )

Returns the part stock offset
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersPatternDirectionTypes NXOpen::CAM::MillCutParameters::PatternDirection ( )

Returns the pattern direction
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

NXOpen::CAM::CutParametersPlungeDirectionTypes NXOpen::CAM::MillCutParameters::PlungeDirection ( )

Returns the plunge direction
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::PreventUndercutting ( )

Returns the prevent undercutting toggle
This property is deprecated.

Use CAM::MillCutParameters::AllowUndercutting and CAM::MillCutParameters::SetAllowUndercutting instead.

Deprecated:: Deprecated in NX8.0.0. Use CAM::MillCutParameters::AllowUndercutting and CAM::MillCutParameters::SetAllowUndercutting instead.

Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::RegionConnection ( )

Returns the region connection
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersRegionSequencingTypes NXOpen::CAM::MillCutParameters::RegionSequencing ( )

Returns the region resequencing
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::RollToolOverEdges ( )

Returns the roll tool over edges toggle
Created in NX6.0.0.

License requirements : None

double NXOpen::CAM::MillCutParameters::RotaryMaxAngleLimit ( )

Returns the rotary max angle limit
Created in NX8.0.0.

License requirements : None

double NXOpen::CAM::MillCutParameters::RotaryMinAngleLimit ( )

Returns the min angle from part axis
Created in NX8.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::SelfIntersection ( )

Returns the Standard Drive Self-Intersect Status
Created in NX6.0.0.

License requirements : None

void NXOpen::CAM::MillCutParameters::SetActionWhenGouging ( NXOpen::CAM::CutParametersActionWhenGougingTypes propValue )

Sets the action when gouging
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the When Gouging Check value

void NXOpen::CAM::MillCutParameters::SetAdjacentBlades ( NXOpen::CAM::CutParametersAdjacentBladesTypes adjacentBlades )

Sets the Adjacent Blades Stock Option Type
Created in NX8.5.0.

License requirements : cam_base ("CAM BASE")

Parameters

adjacentBlades the adjacent blades stock option type

void NXOpen::CAM::MillCutParameters::SetAllowUndercutting ( bool propValue )

Sets the allow undercutting toggle
Created in NX8.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Undercut Handle Flag

void NXOpen::CAM::MillCutParameters::SetApplyToLastPass ( bool applyLastPassStatus )

Sets the status for doing Blank Sensitive finish on the last cut level
Created in NX7.5.1.

License requirements : cam_base ("CAM BASE")

Parameters

applyLastPassStatus apply to last pass status

void NXOpen::CAM::MillCutParameters::SetBoundaryApproximation ( bool propValue )

Sets the boundary approximation toggle
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Boundary Profile Pass Flag

void NXOpen::CAM::MillCutParameters::SetBoundaryInTol ( double propValue )

Sets the boundary intol
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the boundary intol value

void NXOpen::CAM::MillCutParameters::SetBoundaryOutTol ( double propValue )

Sets the boundary out tol
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the boundary out tol value

void NXOpen::CAM::MillCutParameters::SetBoundaryStock ( double propValue )

Sets the boundary stock
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the trim stock value

void NXOpen::CAM::MillCutParameters::SetCornerFindingOptions ( NXOpen::CAM::CutParametersCornerFindingTypes cornerFinding )

Sets the Corner Finding Options
Created in NX7.5.0.

License requirements : cam_base ("CAM BASE")

Parameters

cornerFinding the Finding Corner type

void NXOpen::CAM::MillCutParameters::SetCutBelowOverhangingBlank ( bool propValue )

Sets the Cut Below Overhanging Blank Method
Created in NX9.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Cut Below Overhanging Blank Method

void NXOpen::CAM::MillCutParameters::SetCutBelowToolContact ( bool cutBelowToolContact )

Sets the cut below tool contact setting
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

cutBelowToolContact cutbelowtoolcontact

void NXOpen::CAM::MillCutParameters::SetCutBetweenLevels ( bool cutBetween )

Sets the cut between levels
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

cutBetween the cut between method

void NXOpen::CAM::MillCutParameters::SetCutOrder ( NXOpen::CAM::CutParametersCutOrderTypes propValue )

Sets the cut order
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue propvalue

void NXOpen::CAM::MillCutParameters::SetCutWallsOnly ( bool propValue )

Sets the Cut Walls Only toggle
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Cut Walls Only

void NXOpen::CAM::MillCutParameters::SetExtendFloorTo ( NXOpen::CAM::CutParametersExtendFloorTypes option )

Sets the extend floor to
Created in NX8.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

option the extend floor to option

void NXOpen::CAM::MillCutParameters::SetExtendToPart ( bool flag )

Sets the extend to part flag
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

flag	the extend to part flag

void NXOpen::CAM::MillCutParameters::SetFloorSameAsPartStock ( bool stockPartStatus )

Sets the floor same as part stock
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

stockPartStatus the stock part use status

void NXOpen::CAM::MillCutParameters::SetFollowCheck ( bool propValue )

Sets the follow check geometry status
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Follow Check Geometry Status

void NXOpen::CAM::MillCutParameters::SetGlobalOptimization ( bool globalOptStatus )

Sets the global optimzation status
Created in NX7.5.0.

License requirements : cam_base ("CAM BASE")

Parameters

globalOptStatus global optimization status

void NXOpen::CAM::MillCutParameters::SetIncludeBodiesOfSurfaceRegion ( bool includeBodies )

Sets the flag to check bodies of surface region
Created in NX8.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

includeBodies flag of including bodies of surface region

void NXOpen::CAM::MillCutParameters::SetMinimizeNumberOfEngages ( bool propValue )

Sets the minimize number of engages toggle
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Minimize Number of Engages Flag

void NXOpen::CAM::MillCutParameters::SetPatternDirection ( NXOpen::CAM::CutParametersPatternDirectionTypes propValue )

Sets the pattern direction
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue propvalue

void NXOpen::CAM::MillCutParameters::SetPlungeDirection ( NXOpen::CAM::CutParametersPlungeDirectionTypes propValue )

Sets the plunge direction
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue The plunge direction

void NXOpen::CAM::MillCutParameters::SetPreventUndercutting ( bool propValue )

Sets the prevent undercutting toggle
This property is deprecated.

Use CAM::MillCutParameters::AllowUndercutting and CAM::MillCutParameters::SetAllowUndercutting instead.

Deprecated:: Deprecated in NX8.0.0. Use CAM::MillCutParameters::AllowUndercutting and CAM::MillCutParameters::SetAllowUndercutting instead.

Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Undercut Handle Flag

void NXOpen::CAM::MillCutParameters::SetRegionConnection ( bool propValue )

Sets the region connection
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Region Connection

void NXOpen::CAM::MillCutParameters::SetRegionSequencing ( NXOpen::CAM::CutParametersRegionSequencingTypes propValue )

Sets the region resequencing
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue propvalue

void NXOpen::CAM::MillCutParameters::SetRollToolOverEdges ( bool propValue )

Sets the roll tool over edges toggle
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Remove Edge Traces value

void NXOpen::CAM::MillCutParameters::SetRotaryMaxAngleLimit ( double angle )

Sets the rotary max angle limit
Created in NX8.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

angle the rotary max angle limit

void NXOpen::CAM::MillCutParameters::SetRotaryMinAngleLimit ( double angle )

Sets the min angle from part axis
Created in NX8.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

angle the rotary min angle limit

void NXOpen::CAM::MillCutParameters::SetSelfIntersection ( bool selfIntersect )

Sets the Standard Drive Self-Intersect Status
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

selfIntersect The Standard Drive Self-Intersect Status value

void NXOpen::CAM::MillCutParameters::SetSimplifyShapes ( NXOpen::CAM::CutParametersSimplifyShapesTypes propValue )

Sets the Simplify Shapes Method
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue propvalue

void NXOpen::CAM::MillCutParameters::SetTlaxisBladeRollAngle ( double angle )

Sets the max blade roll angle
Created in NX7.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

angle the max blade roll angle value

void NXOpen::CAM::MillCutParameters::SetTolerantMachining ( bool tolerantMachine )

Sets the tolerant machining status
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

tolerantMachine the tolerant machining status

void NXOpen::CAM::MillCutParameters::SetToolAxisSmoothing ( int smoothing )

Sets the degree of tool axis smoothing
Created in NX7.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

smoothing the Smoothing value

void NXOpen::CAM::MillCutParameters::SetToolpathSmoothing ( int smoothing )

Sets the degree of tool path smoothing
Created in NX7.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

smoothing the Smoothing value

void NXOpen::CAM::MillCutParameters::SetToolRunOffType ( NXOpen::CAM::CutParametersToolRunOffTypes toolRunOff )

Sets the Tool Run Off Type
Created in NX8.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

toolRunOff the Tool Run Off type

void NXOpen::CAM::MillCutParameters::SetTraverseOpenPasses ( NXOpen::CAM::CutParametersTraverseOpenPassesTypes propValue )

Sets the open passes
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue propvalue

void NXOpen::CAM::MillCutParameters::SetTrimControl ( NXOpen::CAM::CutParametersTrimControlTypes propValue )

Sets the trim control method type
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue propvalue

void NXOpen::CAM::MillCutParameters::SetUsePrevious2dIpw ( bool propValue )

Sets the use previous IPW toggle
Created in NX6.0.0.

License requirements : cam_base ("CAM BASE")

Parameters

propValue the Use Previous IPW Flag

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::ShroudStock ( )

Returns the shroud stock
Created in NX7.0.0.

License requirements : None

NXOpen::CAM::CutParametersSimplifyShapesTypes NXOpen::CAM::MillCutParameters::SimplifyShapes ( )

Returns the Simplify Shapes Method
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::SinglePassOffset ( )

Returns the Single Pass Offset
Created in NX8.0.0.

License requirements : None

NXOpen::CAM::SmallAreaAvoidance* NXOpen::CAM::MillCutParameters::SmallAreaAvoidance ( )

Returns the small area avoidance
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::SteepContainment* NXOpen::CAM::MillCutParameters::SteepContainment ( )

Returns the steep containment
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::StepoverBuilder* NXOpen::CAM::MillCutParameters::Stepover ( )

Returns the stepover
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::StepoverLimit ( )

Returns the Stepover Limit
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::TextDepth ( )

Returns the Text Depth
Created in NX6.0.0.

License requirements : None

double NXOpen::CAM::MillCutParameters::TlaxisBladeRollAngle ( )

Returns the max blade roll angle
Created in NX7.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::TolerantMachining ( )

Returns the tolerant machining status
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::ToolAxisChange* NXOpen::CAM::MillCutParameters::ToolAxisChange ( )

Returns the tool axis change
Created in NX6.0.0.

License requirements : None

int NXOpen::CAM::MillCutParameters::ToolAxisSmoothing ( )

Returns the degree of tool axis smoothing
Created in NX7.0.0.

License requirements : None

NXOpen::CAM::ToolAxisTilt* NXOpen::CAM::MillCutParameters::ToolAxisTilt ( )

Returns the tool axis tilt
Created in NX6.0.0.

License requirements : None

int NXOpen::CAM::MillCutParameters::ToolpathSmoothing ( )

Returns the degree of tool path smoothing
Created in NX7.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::ToolRunOff ( )

Returns the Tool Run Off
Created in NX8.0.0.

License requirements : None

NXOpen::CAM::CutParametersToolRunOffTypes NXOpen::CAM::MillCutParameters::ToolRunOffType ( )

Returns the Tool Run Off Type
Created in NX8.0.0.

License requirements : None

NXOpen::CAM::InheritableToolDepBuilder* NXOpen::CAM::MillCutParameters::ToolRunOn ( )

Returns the Tool Run On
Created in NX8.0.0.

License requirements : None

NXOpen::CAM::CutParametersTraverseOpenPassesTypes NXOpen::CAM::MillCutParameters::TraverseOpenPasses ( )

Returns the open passes
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::CutParametersTrimControlTypes NXOpen::CAM::MillCutParameters::TrimControl ( )

Returns the trim control method type
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::TrimStock ( )

Returns the trim stock
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::TrochoidalSettings* NXOpen::CAM::MillCutParameters::TrochoidalSettings ( )

Returns the Trochoidal Settings
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::UpDownCutting* NXOpen::CAM::MillCutParameters::UpDownCutting ( )

Returns the up down cutting
Created in NX6.0.0.

License requirements : None

bool NXOpen::CAM::MillCutParameters::UsePrevious2dIpw ( )

Returns the use previous IPW toggle
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::ValleyOverlapDistance ( )

Returns the valley overlap distance
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::InheritableDoubleBuilder* NXOpen::CAM::MillCutParameters::WallStock ( )

Returns the wall stock
Created in NX6.0.0.

License requirements : None

NXOpen::CAM::ZAxisSmoothing* NXOpen::CAM::MillCutParameters::ZAxisSmoothing ( )

Returns the Z Axis Smoothing.

Created in NX7.5.0.

License requirements : None

The documentation for this class was generated from the following file:

CAM_MillCutParameters.hxx

Public Member Functions

Detailed Description

Member Function Documentation