|
Error No. |
Description |
|
1549000 |
The license for this module is not available/not purchased. |
|
1549001 |
No active part to file. |
|
1549002 |
The HALT or RETURN statement is missing from the program. |
|
1549003 |
The array is too large. |
|
1549004 |
No active part, an active part is required. |
|
1549005 |
This command statement is invalid in GRIP batch mode. |
|
1549006 |
The scratch file is full (too small). |
|
1549007 |
Invalid line number. |
|
1549008 |
Attempt to read past the end-of-file. |
|
1549009 |
The scratch file is not available. |
|
1549010 |
The scratch file has not been initialized. |
|
1549011 |
The selected mesh boundary is not closed, unconnected side 2. |
|
1549012 |
The selected mesh boundary is not closed, unconnected side 3. |
|
1549013 |
The selected mesh boundary is not closed, unconnected side 4. |
|
1549014 |
The number of nodes in the CNL and the number of element boundary nodes are not equal, bad spacing on CNL-1. |
|
1549015 |
The number of nodes in the CNL and the number of element boundary nodes are not equal, bad spacing on CNL-2. |
|
1549016 |
The number of nodes in the CNL and the number of element boundary nodes are not equal, bad spacing on CNL-3. |
|
1549017 |
The number of nodes in the CNL and the number of element boundary nodes are not equal, bad spacing on CNL-4. |
|
1549018 |
Degenerate edges are legal only at the end of a CNL, CNL-1 has a degenerate edge. |
|
1549019 |
Degenerate edges are legal only at the end of a CNL, CNL-2 has a degenerate edge. |
|
1549020 |
Degenerate edges are legal only at the end of a CNL, CNL-3 has degenerate edge. |
|
1549021 |
Degenerate edges are legal only at the end of a CNL, CNL-4 has degenerate edge. |
|
1549022 |
The end of the last CNL does not connect with the first CNL. |
|
1549023 |
A four sided subregion has been selected which has one side that has degenerated into a point. |
|
1549024 |
Sides 2 and 3 of a triangular surface do not have the same number of elements for a vanishing point mesh. |
|
1549025 |
All three sides of a triangular surface do not have the same number of elements for a vanishing point mesh. |
|
1549026 |
Sides 2 and 4 of a four sided surface do not have the same number of elements. |
|
1549027 |
The CNL is outside the value specified in MESH TOL, or the wrong surface was selected. |
|
1549028 |
More nodes needed on shared edge of mesh surfaces, parametric ambiguity. |
|
1549029 |
CNL node order must be in the same direction (clockwise or counter clockwise) on opposite sides. |
|
1549030 |
The EPROP statement contains too few properties. |
|
1549031 |
The EPROP statement contains too many properties. |
|
1549032 |
Property set name does not correspond to the specified element type or the PSET statement contains too few properties. |
|
1549033 |
The PSET statement contains too many properties. |
|
1549034 |
Too few or too many nodes. |
|
1549035 |
Too many CNL labels. |
|
1549036 |
The LOAD number must be greater than zero and less than 10000. |
|
1549037 |
The case number entered for creating a case is used for an existing case. |
|
1549038 |
The specified LOAD case does not exist. |
|
1549039 |
No active LOADS, a case retrieval or create command must precede this command. |
|
1549040 |
A LOAD form number was specified which is not compatible with the current part. |
|
1549041 |
The indicated point coincides with the NODE receiving the LOAD. |
|
1549042 |
The defined LOAD has no vector components for the enforced displacement or rotation. |
|
1549043 |
A case retrieval or create command must precede this command. |
|
1549044 |
None of the ten active elements is valid for the specified LOAD type. |
|
1549045 |
The specified element is not one of the ten active elements. |
|
1549046 |
The number entered does not correspond to a legal edge number for the specified element. |
|
1549047 |
The number entered does not correspond to a legal face number for the specified element. |
|
1549048 |
Too many NODES have been used to define an edge or too few NODES have been used to define a face. |
|
1549049 |
A NODE used to define an element or edge is not on the selected element. |
|
1549050 |
The NODE list specified does not define a legal edge. |
|
1549051 |
The NODE list specified does not define a legal face. |
|
1549052 |
The editor file is not available. |
|
1549053 |
The editor file currently contains a GRIP source file. |
|
1549054 |
The editor file does not contain a CLSF. |
|
1549055 |
The editor file could not be closed by the system. |
|
1549056 |
An analysis language was entered in the FEM statement after the part has been initialized. |
|
1549057 |
The analysis language specified is unsupported. Enter ANSYS, NEUTRAL or NASTRAN. |
|
1549058 |
The surface selected is a closed, 2-sided surface. |
|
1549059 |
The object selected is not a CNL. |
|
1549060 |
An inactive layer has been specified for mesh generation. |
|
1549061 |
Bad mesh node-1, the increment value specified is greater than 32767. |
|
1549062 |
Bad mesh node-2, the increment value specified is greater than 32767. |
|
1549063 |
Bad mesh elm-1, the increment value specified is greater than 32767. |
|
1549064 |
Bad mesh elm-2, the increment value specified is greater than 32767. |
|
1549065 |
The elements chosen for mesh generation are not valid for the analysis language specified for the part. |
|
1549066 |
A bad record has been encountered in the CLSF. The CLSF may no longer be usable. |
|
1549067 |
Invalid record in the editor file. |
|
1549068 |
Unable to create area fill - scale must be greater than 0. |
|
1549069 |
Unable to create area fill - invalid pattern number. |
|
1549070 |
Selected object is not of type boundary. |
|
1549071 |
Selected object is not of type point. |
|
1549072 |
Selected object is not of type line. |
|
1549073 |
Selected object is not of type crosshatch. |
|
1549074 |
Selected object is not of type area fill or solid fill. |
|
1549075 |
Error creating area fill. |
|
1549076 |
Selected object is not a drafting object. |
|
1549077 |
Selected object is not of type crosshatch, area fill, or solid fill. |
|
1549078 |
Selected object is not of type ordinate margin. |
|
1549079 |
Selected object is not of type ordinate dimension origin. |
|
1549080 |
Unable to determine endpoint of object selected. |
|
1549081 |
A NULL object was passed as an argument to the function. |
|
1549082 |
Selected object is not of type arc. |
|
1549083 |
Invalid value for QUAD minor word. |
|
1549084 |
Invalid value for SYMBOL minor word. |
|
1549085 |
Object was not created. |
|
1549086 |
Either or both of position and vector missing for ordinate margin. |
|
1549087 |
Invalid vector for ordinate margin. |
|
1549088 |
No boundary is associated with selected object. |
|
1549089 |
Obsolete error message called. |
|
1549090 |
This is an associated Parameter Set. |
|
1549091 |
Invalid parameter set type. |
|
1549092 |
Invalid tool name. |
|
1549093 |
Invalid parameter set name. |
|
1549094 |
NOPOST is n/a for this case. |
|
1549095 |
No parameter sets linked to tool. |
|
1549096 |
Selected object is not of type planar. |
|
1549097 |
Obsolete error message called. |
|
1549098 |
Change Of Plot Node/Queue Is Not Allowed In PLTSAV or PLTSUB. |
|
1549099 |
Plot Server is inactive. |
|
1549100 |
DCL Processor Error. |
|
1549101 |
Unable to execute GRIP program due to ACS licensing error. |
|
1549102 |
Fail to connect to the plot server. |
|
1549103 |
Unable to display dialog at this time. |
|
1549104 |
Ordinate dimension can only be converted to model or view-dependent by its ordinate origin. |
|
1549105 |
Cannot convert annotation to be dependent upon a drawing view. |
|
1549106 |
Invalid transformation matrix. |
|
1549107 |
The GRIP application and error reporting failed. Please report this problem. |
|
1549108 |
The GRIP program has been aborted. |
|
1549109 |
This command is not supported in External User Function. |
|
1549110 |
INEXTG/HOLOOP requires an active geometry item. |
|
1549111 |
There is no active geometry list. |
|
1549112 |
Cannot read/write GPA because &SSTCTY is not set to &CUSTOM. |
|
1549113 |
Cannot read/write &TOLRV because &TOLRTY is not set to &CUSTOM. |
|
1549114 |
Cannot read/write GPA because &FEEDTY is not set to &CUSTOM. |
|
1549115 |
Orphan operations cannot be retrieved. |
|
1549116 |
Cannot read/write GPA because &CGOUST is not set to &CUSTOM. |
|
1549117 |
Cannot read/write GPA because &CLOPST is not set to &CUSTOM. |
|
1549118 |
No loops in face found. |
|
1549119 |
The geometry selected is not a face. |
|
1549120 |
Must use NEXTG/HOLOOP to have a geometry item. |
|
1549121 |
Machining geometry cannot be created. |
|
1549122 |
Cannot add object to machining geometry. |
|
1549123 |
Fail to delete machining geometry. |
|
1549124 |
Read only GPA cannot be written. |
|
1549125 |
Write only GPA cannot be read. |
|
1549126 |
Invalid maching geometry. |
|
1549127 |
Tool number cannot be negative or greater than 2147483647. |
|
1549128 |
INEXTG/DRIVE does not support this drive method. |
|
1549129 |
INEXTG/DRIVE does not support Boundary drive method, use INEXTG/BND and NEXTG/BND |
|
1549130 |
The command does not support this operation type. |
|
1549131 |
The GPA applies to the current geometry object, it's not applicable to a geometry list. |
|
1549132 |
Invalid object type. The object must be a feature. |
|
1549133 |
Cannot enable features with other entity types. |
|
1549134 |
The license for nurbs toolpath is not available/not purchased. |
|
|
Error number 1548999 is a generic error message for any other type of non-fatal execution errors. Please refer to the error message itself for clues to correct the error. Typically the error message will be self explanatory, but if the error message is not clear you should submit a call to the Global Technical Access Center (GTAC). |
